Launch X431 X-Prog Clone Audi A5 TCU after Replacing Transmission

Launch X431 X-Prog Clone Audi A5 TCU after Replacing Transmission-1 (2)

Using Launch X431 X-Prog Launch x431 scanner to clone TCU for Audi A5 after replacing used transmission will help to skip all security programming and coding steps. That will improve the efficiency to save much time.

X431 X-Prog is an advanced immobilizer & key programmer which also supports VW, Audi, Skoda, Seat, BMW, Mercedes Benz, Toyota… Compatible with X-431 Pro GT, X-431 Pro V4.0, X-431 Pro 3 V4.0, X-431 Pro 5, X-431 PAD III V2.0, X-431 PAD V, X-431 PAD VII.
Launch X431 X-Prog Clone Audi A5 TCU after Replacing Transmission-1 (2)

For normal procedure:

Get security code
Get used transmission security code
Make replacement step
TCM programming
Coding, basic setting…

Why using X431 X-Prog to clone TCU?

Skip all security & programming & coding steps.

It also supports BMW CAS module clone, BMW 8HP clear ISN, MED17 ECU clone and more…

How to use X431 X-Prog to clone TCU?

Enter X431 X-Prog software,

Service function >> immo program >> OK >> OK >> Yes >> OK

The anti-theft key matching adaptor firmware is successfully updated.

Gearbox >> OK >> OK >> DL501 Gen1 >> View wiring diagram

Launch X431 X-Prog Clone Audi A5 TCU after Replacing Transmission-2 (2)Launch X431 X-Prog Clone Audi A5 TCU after Replacing Transmission-3 (2) Launch X431 X-Prog Clone Audi A5 TCU after Replacing Transmission-4 (2)
Please connect the engine to the diagnostic connector according to the pic and power the device on.
Launch X431 X-Prog Clone Audi A5 TCU after Replacing Transmission-6 (2) Launch X431 X-Prog Clone Audi A5 TCU after Replacing Transmission-7 (2)
Connect >> Start the clone process, OK >> Backup EEPROM data >> Input file name to save >> OK >> OK

Backup FLASH data >> input file name >> OK >> OK

Data backup succeeded.

Launch X431 X-Prog Clone Audi A5 TCU after Replacing Transmission-8 (2) Launch X431 X-Prog Clone Audi A5 TCU after Replacing Transmission-9 (2) Launch X431 X-Prog Clone Audi A5 TCU after Replacing Transmission-10 (2)
Press “Disconnect”.

Connect the pin to the transmission need to be replaced.
Launch X431 X-Prog Clone Audi A5 TCU after Replacing Transmission-11 (2) Launch X431 X-Prog Clone Audi A5 TCU after Replacing Transmission-12 (2)
Connect >> OK >> restore EEPROM data >> Select the backup EEPROM file

Data successfully restored!

Restore FLASH data >> Select the backup FLASH file

Data successfully restored!

Launch X431 X-Prog Clone Audi A5 TCU after Replacing Transmission-13 (2) Launch X431 X-Prog Clone Audi A5 TCU after Replacing Transmission-14 (2) Launch X431 X-Prog Clone Audi A5 TCU after Replacing Transmission-15 (2)

Press “Disconnect”.

Clone has been done!

Remember to make a basic setting, the car is ready to drive.

Leave a Comment

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>